Every emergency water removal job includes the full extraction and drying cycle, not just a pump-out. Here is what shows up on your scope, and what we handle as a separate repair once the structure is dry.
Truck-mounted water extraction units and portable extractors pull water from carpet, pad, tile, grout, and hardwood. A sump pump clears deeper basement flooding. We extract until the surface is dry to the touch, not just until the puddle is gone.
A moisture meter, thermal imaging camera, and borescope map where water traveled behind walls and under floors. This is how we find the hidden saturation that turns into mold two weeks after a job that looked finished.
We apply antimicrobial spray to affected framing, drywall, and subflooring after extraction. It slows microbial growth while the structure dries, which matters most on Category 2 and Category 3 losses like sewage backups and appliance leaks.
Air movers and dehumidifiers are placed by calculation, not by feel. A typical 1,000 square foot affected area gets 12 to 18 air movers and 2 to 3 dehumidifiers, sized to the IICRC S500 standard for the materials we are drying.
We return every 24 hours to log readings with a hygrometer and adjust equipment placement. Most residential jobs dry in three to five days. You get the readings in writing, which is the documentation your insurance adjuster needs.
Photos, moisture logs, and a room-by-room scope built in Xactimate. We work directly with your adjuster and can bill the carrier in most cases, so you are not fronting the full cost of a covered loss out of pocket.
Emergency water removal in Utah is the urgent extraction of standing water from a home or business, followed by structural drying that returns wood, drywall, and subflooring to safe moisture levels. It is not a shop vac job. We use truck-mounted water extraction units and portable extractors to pull hundreds of gallons, then place air movers and dehumidifiers to dry the cavities you cannot see. A moisture meter and thermal imaging camera tell us where the water actually went, not just where it pooled.
Most calls we run in Utah start with a burst pipe, a slab leak, a failed water heater, or a sewage backup after heavy spring runoff. Water wicks into insulation and wood subflooring within hours, and mold growth can begin in 24 to 48 hours. If you are searching for emergency water removal near me Utah and the clock is already ticking, that timing matters more than anything else on this page.
You should know exactly what happens after you hang up the phone. Here is the sequence we run on every emergency water extraction in Utah.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Truck-mounted water extraction unit
Pulls hundreds of gallons of standing water from carpet, pad, and hard surfaces far faster than a portable unit, which shortens the drying window on large losses.
Dri-Eaz and Phoenix Restoration Equipment air movers
High-velocity air movers evaporate moisture from surfaces and cavities. We size them by the square footage of the affected area rather than guessing.
Desiccant dehumidifiers
Remove water vapor from the air so it does not re-condense on cool surfaces. Essential in crawl spaces and basements where humidity stays high.
Thermal imaging camera and moisture meter
Find water behind walls and under floors without tearing anything out. This is how we catch hidden saturation before it becomes mold.
Borescope and hygrometer
The borescope inspects inside wall cavities, and the hygrometer reads relative humidity so we know when a space is actually dry, not just dry to the touch.
Sump pump
Clears deeper standing water from basements and crawl spaces where a standard extractor cannot reach the bottom of the pool.
IICRC S500 drying protocol
The industry standard for water damage restoration. It sets how we classify the water, calculate how much drying equipment a space needs, and determine when the structure has reached a dry standard.
Dry standard verification
We take moisture readings from an unaffected room and dry the affected area to match. That number, not a visual check, is what tells us the job is finished.
Xactimate documentation
Every scope is built in Xactimate, the estimating platform most insurance carriers use. That means your adjuster sees line items they recognize, which speeds up approval and reduces back-and-forth.
Antimicrobial application
After extraction, we treat affected framing and drywall with antimicrobial spray to slow microbial growth while the structure dries. On Category 3 losses, contaminated porous materials are removed first.
01
What we do: We shut off the supply, extract the standing water, and pull the saturated carpet pad. The subfloor gets dried with air movers and checked daily with a moisture meter until it matches a dry standard from an unaffected room.
→ Most water heater losses dry in three days, and the carpet can often be re-stretched rather than replaced, which saves you a flooring bill.
02
What we do: We arrive, confirm the break, and extract from the wall cavity before the ice thaws and releases the rest of the water. Insulation is removed, framing is dried and treated with antimicrobial spray, and we document the loss for your carrier.
→ Catching it before the thaw prevents a second flood, and the wall cavity dries in four to five days instead of needing full demolition.
03
What we do: We tarp the roof if needed, extract water from the ceiling cavity, and remove saturated insulation. A desiccant dehumidifier pulls moisture out of the framing while air movers dry the drywall from below.
→ The ceiling dries without a full tear-out in most cases, and you get a documented scope your insurance adjuster can process quickly.
04
What we do: We extract the standing water, map the spread with a thermal imaging camera, and dry the affected rooms. Baseboards are pulled where needed so the wall cavity behind them can dry.
→ A same-day call usually means three to four days of drying and no mold growth, versus a two-week remediation project if it sits.
Utah water losses follow the seasons. From November through March, frozen pipes and ice dam leaks drive most of our calls, especially in older homes from Logan down to Santaquin where supply lines run through exterior walls. Spring runoff floods basements and crawl spaces along the Wasatch Front and in valley towns like Salem and Wallsburg. Summer brings monsoon-driven roof leaks and appliance failures. The building stock matters too. Pre-1978 homes require EPA Lead-Safe practices before we disturb painted surfaces, and Utah's expansive clay soils shift foundations, which is why foundation seepage shows up as a recurring problem in some neighborhoods. When you call for 24 hour emergency water removal Utah, we bring equipment sized for the job and a scope built for your carrier, whether you are in a 1920s bungalow or a new build in Herriman.
Provo
A mix of older brick homes near downtown and newer construction on the east bench. Older homes have more galvanized and polybutylene supply lines, which fail more often.
Cottonwood Heights
Sloping lots and mature landscaping mean roof drainage and foundation seepage drive a lot of our spring calls here.
Herriman
Fast-growing new construction with finished basements. Sump failures and appliance supply line breaks are the most common losses we see.
Coalville
Higher elevation means colder winters and a longer freeze season, so frozen pipe calls start earlier and run later than on the Wasatch Front.
Grouse Creek
Remote and rural, with well systems and outbuildings. We stage equipment for the longer drive and plan for limited water access on site.
Hard freezes from November through March
Supply lines in exterior walls and unheated crawl spaces split when temperatures drop. We see a spike in burst pipe calls after the first hard freeze and again during any mid-winter thaw.
Spring snowmelt and runoff
Saturated ground pushes water against foundations and into basements and crawl spaces. Sump pumps that ran fine all winter get overwhelmed in a single wet week.
Expansive clay soils along the Wasatch Front
Soil movement opens foundation cracks and lets groundwater seep in. Foundation seepage losses often recur in the same homes year after year.
Pre-1978 housing stock in older Utah towns
Lead-based paint is common in homes built before 1978. We follow EPA Lead-Safe practices before disturbing painted drywall or trim during a water loss.
Most of our calls fall into a handful of categories. If yours is on this list, we have run it hundreds of times and know exactly what it takes to dry it out.
Problem
Water pressurizes the wall cavity and saturates insulation and drywall within hours, often without visible pooling on the floor.
Our Fix
We locate the break with a thermal imaging camera, shut off the supply, and extract from the cavity using a borescope-guided approach. Insulation that is saturated gets removed, the framing is dried and treated, and we verify with a moisture meter before closing anything up.
Problem
Water wicks up through the slab and into carpet pad, and the source is invisible, so homeowners often wait days before calling.
Our Fix
We pull the carpet and pad, extract the standing water, and dry the slab surface with air movers and desiccant dehumidifiers. Because slab leaks recur, we document the moisture pattern so your plumber can pinpoint the line before we reinstall anything.
Problem
Category 3 water carries bacteria and pathogens, and anything porous it touches has to be removed rather than dried.
Our Fix
We remove contaminated carpet, pad, and drywall, apply antimicrobial spray, and disinfect hard surfaces. Extraction and disposal follow OSHA and IICRC AMRT protocols, and we document the whole process for your carrier.
Problem
Standing water under the house rots joists, warps wood subflooring, and feeds mold growth that eventually shows up as a musty smell upstairs.
Our Fix
We pump out the standing water, dry the soil and framing with air movers, and install polyethylene sheeting over the ground to block future vapor. A hygrometer reading confirms the space is dry before we close it up.
Water damage gets worse by the hour. These are the outcomes that matter when you are standing in a wet room at 2 a.m.
Fast response, real arrival
We run 24/7 emergency water removal Utah crews, so a burst pipe at 2 a.m. gets the same dispatch as a 2 p.m. call. Most Utah County and Wasatch Front addresses see a technician within 60 to 90 minutes, and we call you with an arrival window instead of leaving you guessing.
Documented for insurance
Every job gets moisture readings, photos, and a room-by-room drying log built in Xactimate, the same estimating platform most carriers use. That documentation is why adjusters approve our invoices without a fight, and why you are not stuck paying out of pocket for damage that was covered.
Mold stopped early
Mold growth can start within 24 to 48 hours of a leak. We apply antimicrobial spray to affected framing and drywall, then verify with a hygrometer that wall cavities are below 16 percent moisture content before we pull equipment. Catching it in the first day is the difference between drying and demolition.
Equipment that finishes the job
We run Dri-Eaz and Phoenix Restoration Equipment air movers and desiccant dehumidifiers, not box fans from a big-box store. A typical 1,000 square foot affected area gets 12 to 18 air movers and 2 to 3 dehumidifiers, sized by the IICRC S500 standard rather than by guesswork.
Emergency water removal cost Utah homeowners pay depends on how much water there is, what category it is, and how long drying takes. Typical 2026 residential pricing runs $1,200 to $3,500 for extraction and dry-out, with small contained jobs starting near $650 and large basement or sewage losses running $5,000 or more. We give you a written price before equipment comes off the truck, and we bill your carrier directly in most covered cases.
Typical Investment Range
$650 - $5,000+ depending on scope
The cost of drying a structure properly is almost always less than the cost of tearing out moldy drywall and replacing a subfloor later. We document everything for your carrier, which means most covered losses end up costing you your deductible and nothing more.
What changes the price
Affected square footage
A single room costs far less than a whole basement. Extraction time, equipment count, and monitoring visits all scale with the size of the wet area, which is why we measure before we quote.
Water category
Category 1 water from a clean supply line is the simplest. Category 2 and Category 3 losses like sewage backups require removal of contaminated materials, antimicrobial treatment, and disposal, which adds labor and cost.
Materials affected
Carpet and pad dry faster than hardwood, tile, or wood subflooring. Materials that cannot be dried in place have to be removed and replaced, and that shows up in the scope.
Drying duration
Most jobs dry in three to five days, but saturated slab or thick framing can take longer. Each additional day means another monitoring visit and another day of equipment rental on the invoice.
Access and containment
Crawl spaces, finished basements with limited entry, and homes with asbestos or lead paint require extra setup. Containment and EPA Lead-Safe practices add time but keep the job safe and compliant.
After-hours dispatch
We run 24/7 and do not charge a separate emergency premium for overnight calls. The price you get is based on the work, not the hour you called.
Google ★★★★★4.9
Called at 1 a.m. about a burst pipe and they picked up on the first ring. Crew was at the house in about an hour, extracted the water, and had drying equipment running before sunrise. The daily moisture logs they sent made my insurance claim easy.
Yelp ★★★★★4.8
Our crawl space flooded after spring runoff and two other companies wanted to just pump it and leave. These guys dried the framing, installed a vapor barrier, and showed me the readings. No musty smell this year.
BBB ★★★★★4.9
Sewage backup in our basement, which is about the worst call you can make. They handled the contaminated material removal and disinfection, worked directly with our adjuster, and the final invoice matched the estimate. Professional from start to finish.
Google ★★★★★5.0
Water heater failed on a Sunday and flooded the hallway. They gave me a price before starting, dried everything in three days, and even re-stretched the carpet instead of pushing me to replace it. Honest work at a fair price.
Our technicians hold IICRC WRT (Water Restoration Technician) and IICRC ASD (Applied Structural Drying) certifications, and several carry IICRC AMRT for microbial work. That training is what separates a crew that dries a floor from one that dries the wall cavity behind it. We work to the IICRC S500 standard on every job, follow EPA Lead-Safe practices on pre-1978 homes, and hold OSHA 10 cards. We are a licensed Utah contractor, insured and bonded, and we document every job the way an adjuster expects to see it.
Our Utah emergency water extraction crews cover the Wasatch Front, the northern valleys, and the rural communities in between. Whether you are in a Provo bungalow or a ranch outside Grouse Creek, we bring the same certified technicians, the same drying equipment, and the same documentation. Call (855) 343-0501 and we will confirm coverage and an arrival window for your address.
Older brick homes near downtown and newer builds on the east bench both see supply line failures. We extract, dry, and document for Provo homeowners and landlords.
Fast-growing Herriman has a lot of finished basements and new appliance hookups. Sump failures and washing machine line breaks are our most common calls here.
Roy sits on the northern Wasatch Front where hard freezes split exterior wall pipes. We handle frozen pipe extraction and wall cavity drying throughout the city.
Sloping lots and mature trees mean roof leaks and foundation seepage. We run extraction and structural drying for Cottonwood Heights homes year round.
Santaquin's mix of older farmhouses and new subdivisions means both aging plumbing and modern appliance failures. We cover both with the same certified crew.
Spring runoff pushes water into Salem basements and crawl spaces. We pump, dry, and install vapor barriers to stop the problem from coming back.
Wellsville's cold winters and rural water systems make frozen pipes a recurring issue. We extract fast and dry framing before mold can take hold.
At higher elevation, Coalville sees a longer freeze season. We stage equipment for the drive and handle burst pipe and crawl space flooding calls.
Henefer's small, tight-knit community gets the same 24/7 response as the Wasatch Front. We handle extraction, drying, and insurance documentation.
Newton homes on well systems and septic see supply line and appliance failures. We extract standing water and dry the structure to a verified standard.
Scipio is rural enough that the nearest plumber is a drive away. We bring extraction and drying equipment with us so the job gets done in one trip.
Wallsburg sits in a valley where snowmelt drains toward foundations. We handle basement and crawl space flooding with pumps and desiccant dehumidifiers.
Lynndyl properties are spread out and often include outbuildings. We plan for the drive and bring enough equipment to dry the whole loss in one setup.
Grouse Creek is remote ranch country with limited water access on site. We stage equipment ahead of the drive and handle extraction and drying start to finish.
Real answers to the questions we hear most often from local homeowners and property managers.
Extraction is only the first phase. Our water damage restoration service rebuilds what the water ruined, from drywall and insulation to paint and trim, so your Utah home is put back the way it was before the leak.
View Water Damage RestorationWhen runoff or a storm pushes muddy water into your home, flood cleanup goes beyond extraction. We remove contaminated material, disinfect surfaces, and dry the structure so bacteria and odor do not linger in your Utah property.
View Flood CleanupBasements flood fast and dry slow. Our basement water extraction crews use sump pumps and truck-mounted units to clear standing water, then set drying equipment sized for below-grade spaces where humidity hangs around longer.
View Basement Water ExtractionCrawl space moisture rots joists and feeds mold long before you smell it upstairs. We remove standing water, dry the soil and framing, and lay polyethylene sheeting to keep ground moisture from wicking back into your Utah home.
View Crawl Space Water RemovalA sewage backup is Category 3 water and needs more than a wet vac. We remove contaminated materials, apply antimicrobial spray, and disinfect the space so your Utah home is safe to live in again.
View Sewage Backup CleanupAfter a Utah storm drives rain through a roof or window, we tarp, extract, and dry. Storm damage restoration covers the water removal and the repairs so you are not juggling separate contractors while your ceiling drips.
View Storm Damage RestorationCall us at (855) 343-0501 any time, day or night. A live dispatcher answers, not a machine. We serve the entire state of Utah and can have a crew at your door within 60 to 90 minutes for most Wasatch Front addresses. You can also email [email protected].
Phone
(855) 343-0501Address
Utah
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available
